Welcome to HUABO Machinery · Custom Machinery Parts Factory — Quality You Can Trust
Home/News/Material Guide
MATERIAL GUIDE · Gear Steel

20CrMnTi Gear Steel Guide: Carburizing, Properties & Transmission Uses

Source: HUABO MachineryAuthor: HUABO Editorial TeamPublished: November 3, 2026

Behind a large share of the world's hardened transmission gears sits one Chinese grade: 20CrMnTi. It is the carburizing steel that gives a gear a hard, wear-resistant case and a tough, shock-absorbing core — at a cost that keeps it on automotive, agricultural and construction-equipment lines worldwide. This 2026 guide covers its chemistry, international equivalents, heat treatment and where it belongs in a transmission.

What Is 20CrMnTi Designed For?

20CrMnTi is China's standard carburizing gear steel under GB/T 3077 — a low-carbon chromium-manganese-titanium alloy built for case hardening: carburize, then quench, to produce a hard wear-resistant surface over a tough core. Titanium refines grain and boosts hardenability, raising tooth-root fatigue strength.

Typical parts: transmission gears, pinions, gear shafts, ring-gear blanks and spline shafts operating under repeated contact load, friction and shock.

Carburized 20CrMnTi transmission gears and gear-shaft blanks precision machined at HUABO, Ningbo.
Carburized 20CrMnTi transmission gears and gear-shaft blanks precision machined at HUABO, Ningbo.

Chemical Composition (GB/T 3077, wt. %)

CSiMnCrTiP (max)S (max)
0.17–0.230.17–0.370.80–1.101.00–1.300.04–0.100.0300.030

20CrMnTiH is a related grade with specified hardenability bands under GB/T 5216. Confirm the exact standard and hardenability band on your drawing before ordering.

International Equivalents — the Honest Answer

20CrMnTi has no exact AISI or EN twin. Functionally it sits in the carburizing family of SAE 8620 / 4320 (USA) and 20MnCr5 / 16MnCr5 (EN/DIN), but chemistry and case-hardening response differ — they are alternatives, not drop-in equivalents.

RegionGradeNote
China20CrMnTi / 20CrMnTiHGB/T 3077 / GB/T 5216
Europe20MnCr5 (1.7147)Closest EN grade — verify
USASAE 8620 / 4320Same family, not identical

Carburizing & Heat Treatment

Gears are typically carburized to an effective case depth of about 0.8–1.2 mm with surface carbon near 0.8–1.0%, then quenched and low-temperature tempered. Result: surface hardness roughly 58–62 HRC for wear and contact-fatigue resistance, while the core stays tough at about HV 320–450 to absorb transmission shock. Low-temperature carburizing variants further reduce distortion and extend fatigue life for high-speed, heavy-load drives.

Why Forge Gear Blanks?

Forged gear blanks put the fibre flow along the tooth profile instead of cutting through it — delivering materially better fatigue life than gears machined from bar, while reducing machining allowance. See HUABO's helical gears, spline gear shafts and automotive transmission forgings, produced from 20CrMnTi and related carburizing grades.

Applications

  • Automotive — gearbox gears, pinions and drive shafts
  • Construction machinery — travel/ring gears and transmission parts
  • Agricultural equipment — drivetrain and transmission components
  • Industrial transmissions — reducers and precision hardware drive parts

Frequently Asked Questions

What is 20CrMnTi steel equivalent to in ASTM?

There is no exact ASTM equivalent. Functionally it belongs to the carburizing family of SAE 8620/4320 (USA) and 20MnCr5/16MnCr5 (Europe) — related but not interchangeable. For a project that must meet a US or EU designation, order the specified grade.

Is 20CrMnTi suitable for carburizing and quenching?

Yes — that is its main purpose. After carburizing and quenching, gears reach roughly 58–62 HRC surface hardness with a tough core, combining wear resistance with shock absorption. Titanium refines grain so case depth stays stable at carburizing temperature.

What hardness does 20CrMnTi reach after case hardening?

Typical surface hardness is 58–62 HRC over an effective case depth of about 0.8–1.2 mm, while the core remains tough at approximately HV 320–450. Exact values depend on the agreed heat-treatment spec and section size.

Can HUABO supply forged 20CrMnTi gear blanks?

Yes. We forge and machine gear blanks, pinion shafts and ring gears to drawing, and supply them normalized or as-forged ready for your carburizing line. Send your drawing for a factory-direct quote.

Looking for a reliable custom machinery parts factory in China? Contact HUABO Machinery with your drawings and material requirements — as a source factory in Ningbo, we deliver factory-direct pricing, engineering support and OEM/ODM manufacturing.

20CrMnTiCarburizing SteelGear Steel8620 EquivalentForged Gear BlanksOEM / ODM
Back to News List

Need Carburizing Gear Blanks or Transmission Parts?

Send your drawing, grade and case-depth spec — get a factory-direct quote within 24 hours.

Get Quote